Free AVIXA Audiovisual Network Professional (ANP) exam Practice Questions

Sample Practice Questions

Try these 10 sample questions from the AVIXA Audiovisual Network Professional (ANP) exam practice bank. Each includes the answer and explanation. Continue with the interactive practice above to review the full question set.

1. 1A client expects its IT department to provide the AV network, while the integrator expects to supply it. What should the scope of work establish before implementation?

   1. A.Assign network provision to a named party and obtain agreement.Correct answer: A
   2. B.List the network equipment and leave provision to field coordination.
   3. C.Use the phrase complete AV solution to imply joint responsibility.
   4. D.Defer network ownership until the acceptance demonstration.

   Explanation: AVIXA describes roles and responsibilities as "Who is accountable for which tasks?" The SOW should resolve network provision explicitly so the client and integrator agree on ownership before implementation.

   Reference: The Power of a Well-Crafted Statement of Work in AV Projects — Why the SOW is the Backbone of AV Projects — Roles and Responsibilities

2. 2A small Dante installation will use a 100 Mbps switch for fewer than 32 channels. Which switch capability must be present and active for this limited configuration to meet Audinate's guidance?

   1. A.Quality of Service for prioritizing Dante traffic.Correct answer: A
   2. B.Power over Ethernet for powering all connected endpoints.
   3. C.Optical uplinks for every inter-switch connection.
   4. D.Dual power supplies for continued switch operation.

   Explanation: Audinate requires "proper QoS" for this 100 Mbps case. PoE, fiber, and redundant supplies do not replace packet prioritization.

   Reference: Networks and Switches — What is the minimum requirement for switches in a Dante network?

3. 3A new Q-SYS peripheral requires a later release than the system currently uses. Which software integration plan addresses the combined inventory?

   1. A.Select a supported release that accommodates both new and retained hardware.Correct answer: A
   2. B.Retain the old release because it supports all currently installed hardware.
   3. C.Select the new peripheral's minimum release without checking retained devices.
   4. D.Install the newest release without reviewing either hardware support list.

   Explanation: New hardware is "not backward-compatible" with earlier releases. Select a release supporting the combined inventory.

   Reference: Q-SYS Designer Software Compatibility — As a rule — hardware introduced in a release

4. 4An AV equipment room has been cleaned, but sanding is scheduled inside it tomorrow. Which readiness conclusion follows the clean-building handover guidance?

   1. A.Release the room based on today's absence of visible dust.
   2. B.Release the room after covering equipment during tomorrow's sanding.
   3. C.Defer release until contaminating work ends and cleanliness is verified.Correct answer: C
   4. D.Release the room now and clean installed equipment after sanding.

   Explanation: The guide requires "no further work" that releases contaminants. A clean room with planned sanding is not ready for equipment installation.

   Reference: Audiovisual Systems Performance Verification Guide — PHYSE-105 Clean Building Handover, p. 133

5. 5A networked AV system has several sources and destinations. One successful source-to-display test has been completed. What additional verification follows AVIXA's commissioning guidance?

   1. A.Treat that route as proof that every route works.
   2. B.Test every required audio, video, and control path.Correct answer: B
   3. C.Test only that every device appears in discovery.
   4. D.Test only that every network port shows link.

   Explanation: AVIXA calls for checking "every audio, video and control path". One successful route does not verify all required paths.

   Reference: Let’s Talk AV with Alexis — Episode 3: Commissioning, Where AV Design Becomes Reality — Key Objectives of Commissioning — Signal Path Verification

6. 6Commissioning changed several AV processor settings and connections from the original design. Which closeout action preserves an accurate installation record?

   1. A.Deliver only the original proposal drawings.
   2. B.Remove the changed devices from the handover package.
   3. C.Update installation drawings to reflect the final changes.Correct answer: C
   4. D.Rely on the commissioning technician's memory.

   Explanation: Extron requires "update installation drawings" after adjustments. Original design intent alone does not record the final installed system.

   Reference: Product Commissioning — Why Extron System Commissioning?

7. 7An AV network proposal includes classroom streaming but leaves corridor displays undecided. How should the scope document address the corridor displays?

   1. A.Include their equipment cost while leaving installation undefined.
   2. B.State explicitly whether they are included in the agreed work.Correct answer: B
   3. C.Treat their presence on a floor plan as authorization to install them.
   4. D.Assume that displays outside classrooms are covered by the same scope.

   Explanation: The SOW identifies scope as "What is included". Explicit inclusions and exclusions settle the engagement boundary; a cost entry, floor plan, or unstated assumption does not settle the disputed work.

   Reference: The Power of a Well-Crafted Statement of Work in AV Projects — Why the SOW is the Backbone of AV Projects — Scope of Work

8. 8An existing fiber backbone meets the required Ethernet link specifications. Which design conclusion follows from Dante's standards-based networking?

   1. A.The backbone can carry control but must exclude Dante audio.
   2. B.Compatible Ethernet switches can carry Dante over the backbone.Correct answer: B
   3. C.The backbone must be replaced with copper to carry Dante audio.
   4. D.Every Dante endpoint must have its own optical connector to use the backbone.

   Explanation: Audinate supports "fiber connections". Ethernet switches can bridge copper endpoint connections to a suitable fiber backbone.

   Reference: Networks and Switches — Does Dante work with Fiber Optic network cable?

9. 9A Q-SYS design uses properties introduced in a newer QDS release. What should be assumed before handing the file to a team using an older release?

   1. A.The file will open after changing its filename extension.
   2. B.The new properties are automatically translated into equivalent old properties.
   3. C.The file may not open and requires a compatibility check.Correct answer: C
   4. D.Only the drawing colors can differ between the two releases.

   Explanation: Designs using newer features "might not open" in older QDS versions. Backward file compatibility must be checked.

   Reference: Q-SYS Designer Software Compatibility — Note — designs with newer hardware, features, or properties

10. 10Before mounting networked AV equipment, how should installed backing and framing be verified?

    1. A.Verify backing configuration, placement and compatibility with the mounting design.Correct answer: A
    2. B.Accept backing in any position if its material matches the design.
    3. C.Accept the specified location without checking backing compatibility with the mount.
    4. D.Accept suitable backing dimensions without checking its installed placement.

    Explanation: The guide requires "configuration, placement, and compatibility". Finished walls alone do not verify the intended structural accommodation.

    Reference: Audiovisual Systems Performance Verification Guide — PHYSE-104 Backing/Blocking/Framing, p. 133